DIY Thin Tile Brick Project
September 5, 2018
It’s time to work with DIY’ing your floor tile shower as well as you’re not expecting dealing with the dreadful concrete board once more. It’s dirty, brittle, and also difficult to begin screws right into. In addition to just how hefty it is.
Certain, there are water-proof foam backer boards on the marketplace however they are extremely pricey. Just what to do?
Well, this is a location where GoBoard is fairly engaging: It sets you back dramatically much less compared to various other foam backer boards yet is a lot easier and also less complex to mount compared to concrete board.
GoBoard floor tile backer board is water-proof. Certainly, you’ll need to secure the joints and also infiltrations like you would certainly with any type of backer board. GoBoard itself is water resistant as well as does not obtain an added waterproofing included to it. Unlike several of the various other preferred foam backer boards that need their very own brand name of unique screws and also washing machines, GoBoard is set up with concrete board screws or galvanized roof covering nails After that when you consider the convenience of waterproofing, pointed out over, as well as the price financial savings as compared to various other foam backer boards, you could see exactly how all this amounts to rather an engaging item. I was mounting the wall surfaces around a recess bathtub. Given that a conventional bathtub is 60 inches broad I do not believe it’s a coincidence that floor tile backer boards come 60 inches in size. For the back wall surface, I laid the panels sidewards so they were 36 inches high. The side wall surfaces I mounted up and down.
I a lot like screws although they are possibly one of the most time consuming of the selections detailed above. Because it’s very easy to drive the screws as well deep you’ll need to take care concerning exactly how much the screws are mounted. If the screws typically aren’t screwed in much adequate after that they will certainly hinder the sealer as well as you can endanger the waterproofing of the panels. If they are driven also much in after that they will not have the holding power. See to it to use sealer in between the bathtub as well as GoBoard panels. In the video clip, I reveal my very own strategy for this which is not called for. The essential point is to earn certain that void obtains secured.
Tidy up as well as last actions – I located the sealer to tidy up with denatured alcohol. You could utilize this around the bathtub or shower additionally to cleanse the GoBoard sealer off
Trimming glass ceramic tile could be an obstacle. Yes, even more of a difficulty compared to reducing routine old ceramic floor tile. Furthermore, the typical DIY’er could not have the appropriate devices as well as might unknown the methods for ways to reduce glass floor tile.
Just what makes glass floor tile tough to reduce is that you could translucent it. This makes any type of flaws simply noticeable. Numerous glass ceramic tiles are clear throughout as well as have a finish on the back which provides their shade. This finishing could chip off as well as end up being jagged from reducing on a damp saw (ceramic tile saw). Frequently, this will certainly reveal when seen from an angle. Furthermore, several DIYers have the less costly “table saw” kind floor tile saws and also will certainly need to change the ideas to fit. Pointer # 1: Cut the glass ceramic tile upside down will certainly suggest reducing it right-side-up on a saw where the blade comes up from below
The reasoning for reducing glass floor tiles upside down is that the glass floor tile blade will certainly reduce the covering on the back. Given that the turning of the blade indicates that it’s getting in with the finishing the “burn out” would certainly get on the glass side.
Yes, I comprehend that this suggests that the front side of the thin tile brick will certainly have the rougher of both cuts. If the front side could be fined sand, or submitted down, so that it’s smooth after that this will certainly supply a good-looking cut.
If you’re reducing glass ceramic tile that is a strong shade without any support you’ll intend to neglect this method and also suffice the “typical” method.
This is a comparable idea as above. The a lot more that the blade enters into call with the layer the most likely you are to chip the finish as well as have defects reveal with to the front of the floor tile.
When reducing glass ceramic tiles, it prevails to press the ceramic tile via the saw blade and afterwards draw it back prior to closing the floor tile saw off. Utilizing this strategy, you would just press it with as well as after that transform the saw off and/or divide the floor tile prior to drawing the rolling tray back as suggested by https://www.cletile.com/.
This protects against the saw blade from entering call with the glass floor tile as well as aids to avoid more breaking of the glass. My individual experience is that a glass ceramic tile ruby blade does a better task compared to a normal ceramic tile saw blade. Glass floor tile blades have finer as well as softer rubies that produce a smoother cut. It will certainly take longer to press the ceramic tile via the saw with a glass ceramic tile blade however the outcomes are typically for the much better.